Keys-fitness Power System 1850 Instrukcja Użytkownika

Owner’s ManualRead all precautions and instruc-tions in this manual before usingthis equipment. 215-0000909/04

STEP 1 Insert the two Guide Rods (24) into Rear Base (1) and secure them in place using two Washers (102), twoSpring Washers (103), and two Allen Bolt

Assembly11STEP 2Attach the Seat Pad Support Receptacle (2) to Rear Base (1) and secure in place using three Nylon Locknuts(104), six Washers (102), an

Assembly12Step 3Install the Main Upright (3) onto Seat Pad Support Receptacle (2). Secure it in place using three NylonLocknuts (104), six Washers (1

Assembly13Step 4Slide one Weight Stack Bumper (30) down each Guide Rod (24). Next, slide the weight plates down theGuide Rods (24) in this orde

Step 5Attach Press Arm Support (5) to Main Upright (3) by aligning the holes and sliding the Shaft (74) through. Secure the Shaft (74) in place u

Assembly15Step 6Slide the Right Pec Dec Arm (8) on to the shaft of the Pec Dec Mount (7). Secure the arm in place usingone Big Washer (76), one Washe

Assembly16Step 7Install the Right and Left Hold Leg Frames (17 & 18) to Main Upright (3) and secure using two NylonLocknuts (104), four Washers (1

Assembly17Step 8Slide the Shaft (72) into the Leg Extension Lever (10). Attach Leg Extension Lever (10) to Seat PadSupport Receptacle (2) and secure

Assembly18Step 9Attach the Seat Pad (26) to the Seat Pad Support (13) using two Washers (102) and two Allen Bolts (96).Slide the Seat Support assembly

Assembly19Step 10Slide two Upholstered Roller Pads (42) onto Foam Frames (11 & 12) and secure using two Big Plugs (65).Slide the Long Foam Tube (7

Table of Contents2Important Safety Information 3Before You Start 4Assembly 5-26Weight Ratios 27Weight Stack Sticker Placement 28Cable View 29Top View

Assembly20Step 11Note: Stretch all cables out completely and make sure all twisting is removed before installing. Install Chest Press Cable (45) as d

Assembly21Step 12Note: Stretch all cables out completely and make sure all twisting is removed before installing. Install Mid Pulley Cable (46) as de

Assembly22Step 13Note: This step is only used if you do not have the Leg Press 2 attachment. Use the Cable Adapter (113) inplace of the pulley.Note:

Assembly23Step 14Note: Stretch all cables out completely and make sure all twisting is removed before installing. Install Pec Dec Cable (49) as detai

Assembly24Step 15Connect Long Lat Bar (70) to the Chest Press Cable (45) using two Gear Hooks (33) and Short Chain (35).Connect Ab Strap (40) or Lat S

Assembly25Step 16Install Weight Shrouds (20) to each side of the Main Top Beam (4) using two Washers (102), two SpringWashers (103), and Allen Bolts (

Assembly26Congratulations!You have completed the assembly of your new KPS-1850.

Weight Ratios27KPS-1850Weight(lbs) 100% 95% 90% 65% 45%10 10 9.5 9 6.5 4.515 15 14.25 13.5 9.75 6.7520 20 19 18 13 925 25 23.75 22.5 16.25 11.2530 30

Weight Stack Sticker Placement28101015202025304050607080901003035455565758595105115115125140155170130145160175190205220235250185200200 LB Stack250 LB

Cable View29

Important Safety Information3THANK YOU for making this Power System unit a part of your exercise pro-gram. Keys Fitness and our Power System Series a

Top View30

Exploded View31

REF# KEYS PART# DESCRIPTION QTY. REF# KEYS PART# DESCRIPTION QTY.1 223-00235 Rear Base 1 61 206-00020 Square Plug 44.5 22 223-00236 Seat Pad Support R

Warranty InformationKEYS FITNESS PRODUCTS, L.P.POWER SYSTEM SERIES LIFETIME WARRANTYThis Warranty applies in the United States and Canada to products

Customer Service1.888.340.0482Keys Fitness4009 Distribution DriveSuite 250Garland, TX 75041www.keysfitness.com

Before You Start4Prior to assembly, remove components from the box and verify that all the listed parts were supplied. SAFETY INFORMATION WARNING!Bef

Assembly5Box 1

Assembly6Box 2

Assembly7Box 3Box 5 Box 6Box 4

Assembly8

Assembly9